Y09-3016
Laser Particle Counter
Instruction Manual
Catalogue
I. Principle Introduction
II. Main Characters and Parameter
III. Application
IV. Function Instruction
V. Operation Instruction
VI. PC software Operation
VII. Attachment
I. Principle Introduction
Y09-3016 Laser Particle Counter adopts the principle of light scattering, when the suspended particles in the air after a photosensitive area, scattering and its particle size with a certain proportion of luminous flux, get treated by photoelectric conversion, amplification and be harvested equivalent diameter and number of particles.
II. Main Characters and Parameter
1.Overall size:130*220*45mm³(W*D*H)
2.Relative Humidity: 20--75﹪RH
3.Max power:8W
4.Power supply:
5.Particle size distribution channel:0.3、0.5、1、3、5、10（µm）
6.Sampling flow:2.83L/min
7.Temperature: 10-30℃
8.Relative Humidity: 20--75﹪RH
9.Aerosphere Pressure: 86-106kPa
10.Maxim Dust Concentration: 35000particles/ m³@0.5µm
11.Self-purification time:≤10min
III. Application
This counter is used to measure per unit volume in clean environment in the air of dust particle size and number, can be directly testing the cleanliness level for the clean environment in grade three hundred thousand to ten.
This instrument adopts the semiconductor laser light source, LCD display, its small volume, light weight, high detection accuracy, operation simple and clear function, computer control, can be stored, printed sampling results, test the clean environment is very convenient.Widely used in electronic, optical, chemical, food, cosmetics, medicine, biological products, aerospace and other departments for public health.
IV. Function Instruction
■Front panel
Contains the LCD panel and eight function keys:
“Reset”, “Test”, “Print”, “Exit”, “▲”, “▼”, “OK”, “Mode”
LCD display is controlled by computer, the process as show below:
Boot screen:
1.Setting screen:
Press “OK”to enter the setting screen
Each time you press the "▼" button, the cursor is in turn down, each time you press the "▲" button, when the cursor move in turn, accompanied by warning tone.When the cursor moves to date, press the "OK" button to enter interface adjustment date. Press the "OK" button to save the current Settings and exit.Other functions set up the same operation.
Measuring location: 000-999 arbitrary adjustable, 000 said don't care about the location, the rest can be set for yourself.
Clear data: data for clear memory, 0 :no clear memory, if you want to remove the memory will be according to "OK" button change 0 to 5,then press “OK”.Numbers turn to nine said clear all memory((Do not easily turn to 5)
2.Searching screen:
Press “OK”again, the searching screen as show below:
Screen to the upper right corner of the F: 0.00 L/min said sampling pump closed, T: 00060 smeans sampling period to 60 seconds.0.3, 0.5, 1, 3, 5, 10 (including m) said sampling particles particle size, the value behind the number show the quantity ofparticles.L: 000 saidthe address number is 0, 2016/10/12 said the last time sample save date, joyfully said the last time samples to save time.W: OFF said close observation function.P: OFF said printing function to shut down, press the "Print" button to open (ON).S: OFF said close the saving function, press "OK" button to open (ON).R: 0012/1000 means itstores the data of the 12datain Max 1000.According to "bring" or "▼" key can watch store measurement data.
3.Testing screen:
Press “Test”button to sample:
After press "sampling" button, the screen F: 0.00 L/min to F: 2.83 L/min (sampling flow).T: 060 into T: 00001/060 incremental change (001-001), when press the "mode" key to open the W: ON, said observe function open, screen real-time display the current cycle change as shown in figure 6, the number of sampling particles the function of the "mode" key to switch between the three kinds of display mode.
V. Operation Instruction
1.Preparation
(1). Open the power switch, press the "OK" key to screen set totestinginterface, watch battery symbol, if the battery is not enough, then insert the ac adapter "outlet", to recharge the battery, the instrument at the same time also can be used for normal operation.
(2). Preheat for oneminute.
(3). Connect with the sampling port and filter port,press”OK”twice to enter testing interface. Open the “Test”to make the instrument from the net zero.
(4).The operation steps
The sampling head in the “sample”
Under the setting screen press “▲”, “▼”and “OK”button to set the required parameters. If database reset, move the cursor to the data reset,(the number 0 turn to 5 number) then press “OK”until number change into the “9”. If do not modify the working parameters, press”OK”button to enter directly testing interface.
Press the "OK" button to enter after measuring interface, press the "Test", open the pump source sampling test, the collected data.If ideal sampling results, press the "OK" key, the LCD screen below the "Rec" to ON, sampling data storage, or press "OK" button, the "Rec" to OFF.Press the "Mode" button, switch display mode.According to "▲" and "▼" key, in the first and the third state can flip observe one cycle before sampling record.Then press the "Test", it is closed.
When testing interface, if need to change the working parameters, press "Exit" to return to the parameter setting state
VI.PC softwareOperation
1.Find the instruments attached the delivery of the U disk, its internal file copy and the software to a computer.
2.software driver installation, double-click the software driver package or unzip the files, double-click the subdirectory "setup.exe file, click on the installation, the installation is complete will popup dialog prompt after the installation is complete.
3.End, with the probability of the USB cable link instruments, end link to the computer.
4.Open the instrument power supply, do not click the "start" button, sampling interface communication if click on this button will lead to abnormal, cause data errorsdouble-click on a computer at this time "the dust particle counter data acquisition system", the software install software for free.Interface as shown in the figure below:
Screen as following:
5.Click on "connect" button interface, the software will automatically identify instrument type and serial number
6.Click the interface "collect" button, the software will automatically read the instrument on the test data, if the number is more, to read the time will be slightly longer
click "query" button on the interface, will pop up the following
dialog:
7.Here only provide according to the time query mode, the query please tick in the box, before the time and select the start time and click "ok" button, query this period of time to collect data.
8.Click "Delete" button on the interface, will delete alldata within the instrument, if you want to delete the local data, please click on the "Derive" button, the data can be exported to a computer and save into EXCEL format text, just modify, and delete data in EXCEL
9.Click after measuring data type drop-down dialog box, can be in "particle counting sampling data" and "particle counting confidence data" switch.
VII. Attachment
ISO standard：Clean room and clean area selected columns of suspended particle cleanliness level
ISO Level（N）Be considered in the table is greater than or equal to the maximum concentration limit of particle size（pc/m3Air concentration limit according to the formula in 3.2）
0.1μm0.2μm0.3μm0.5μm1μm5μm
ISO Class 1102
ISO Class 210024104
ISO Class 31 000237102358
ISO Class 410 0002 3701 02035283
ISO Class 5100 00023 70010 2003 52083229
ISO Class 61 000 000237 000102 00035 2008 320293
ISO Class 7352 00083 2002 930
ISO Class 83 520 000832 00029 300
ISO Class 935 200 0008 320 000293 000
Note：Because of the uncertainty of the measurement process, the requirement with three effective data to determine the concentration of grade level.
If there are problems cannot be solved, please contact with:
Tel： +86 0575 81275735
